Характеристики
- Грузоподъёмность
- нет данных
- Вылет
- нет данных
- Повторяемость позиционирования
- нет данных
- Масса
- нет данных
- Степень защиты
- нет данных
Характеристики из источника
Строки приведены так, как их печатает производитель: без перевода, пересчёта и сравнения.
- Store Config to E2 POR Defaults Cmd (01h)
- 61 h (Period setting PWM0)
- Address Register
- 27 h (Reserved None)
- xxxxx100b
- 367.6 Hz ((programmable))
- Table 6. Device Register Address Map
- 26 h (Reserved None)
- Inversion Register (1Bh)
- 22 h (Slow Strong Drive Strong High, Strong Low,)
- xxxxx011b
- 93.75 kHz
- Divider (1-255)
- 93.75 kHz
- bus
- 1. A
- Figure 8. GPIO Timing Diagram
- 90 %
- Table 6. The Device Register Address Map
- 26 h (Reserved None)
- jitter
- 1. A
- Command Register (30h)
- 00h–07 h (Output Port 0–7)
- Commands Description
- 60 h (Config setting PWM0)
- xxxxx000b
- 32 kHz
- configuration as new POR defaults, restore factory defaults,
- 10h–17 h (Select PWM Port 0–7)
- The current ports settings (drive modes and output data) and
- 62 h (Pulse Width setting PWM0)
- synchronous
- 1. A
- jitter
- 93.75 kHz (and 367.6 Hz)
- Store Config to E2 POR Defaults Cmd (01h)
- 62 h (Pulse Width setting PWM0)
- define POR defaults, read POR defaults, write device
- 18 h (–1Fh Inversion Port 0–7)
- Interrupt Pin (INT)
- 367.6 Hz (-)
- with stored POR defaults. The command set is presented in
- 20h–27 h (Pin Direction Port 0–7)
- noise
- 1. A
- block
- 1. A
- Restore Factory Defaults Cmd (02h)
- 91 h (Enable)
- Cload = 50 pF
- 10%–90 %
- Note
- 3. A
- buffer
- 1. A
- active high
- 1. A (logic signal having its asserted state as the logic 1 state.)
- bias
- 1. A (systematic deviation of a value from a reference value.)
- Command Register (30h)
- 08 h (–0Fh Interrupt mask Port 0–7)
- GPort 1 3 Bit IO
- 93.75 kHz
- Notes
- 3. A
- There are six available clock sources
- 32 kHz ((default), 24 MHz,)
Источники
- CY8C9520A
страница товара; от производителя; издатель: Infineon; редакция: 2026-10-03
Где в источнике: Store Config to E2 POR Defaults Cmd (01h); Table 6. Device Register Address Map; Figure 8. GPIO Timing Diagram; The current ports settings (drive modes and output data) and; define POR defaults, read POR defaults, write device; Interrupt Pin (INT); Command Register (30h); GPort 1 3 Bit IO; Notes
- CY8C9520A
технический лист; от производителя; издатель: Infineon; редакция: 2026-10-03
Где в источнике: Address Register; xxxxx100b; Inversion Register (1Bh); xxxxx011b; Divider (1-255); bus; Table 6. The Device Register Address Map; jitter; Command Register (30h); Commands Description; xxxxx000b; configuration as new POR defaults, restore factory defaults,; synchronous; Store Config to E2 POR Defaults Cmd (01h); with stored POR defaults. The command set is presented in; noise; block; Restore Factory Defaults Cmd (02h); Cload = 50 pF; Note; buffer; active high; bias; There are six available clock sources